How to make an LED 4X4X4 cube with Arduino Uno?

  March 24, 2020
      No Comments

How to make an LED 4X4X4 cube with Arduino Uno?

LED CUBE 4X4X4 USING ARDUINO UNO

  1. Introduction: LED CUBE 4X4X4 USING ARDUINO UNO.
  2. Step 1: List of Materials.
  3. Step 2: Preparation of Jig to Place the LED.
  4. Step 3: Placing the LEDs on the Jig and Soldering.
  5. Step 4: Solder the 4 Layers.
  6. Step 5: Wiring the LED Cube to Arduino.
  7. Step 6: ​Programming the Arduino.

How do you make a 4 4 4 LED cube?

Making the Cube Layers

  1. Put in the LEDs along the back and along one side, and solder them together.
  2. Insert another row of LEDs and solder them together.
  3. Repeat the above step 2 more times.
  4. add cross bracing in the front where the led rows are not connected.
  5. Repeat 4 times.

What is a LED cube?

Basically an LED cube is a 3 dimensional cube made out of Light Emitting Diodes (LEDs). The Cube can be made in various ways but for this project, a simple setup is used that is controlled by an Arduino Uno microcontroller.

What is the use of LED Cube?

The Purpose The main purpose that the L3D Cube serves is in the entertainment sector. For all intents and purposes, it is actually a high-tech display. Think of it as a three-dimensional display consisting of 512 pixels (or voxels in this case) which can be used to visualise any sort of animation or graphics.

How do you make a 3d LED Cube?

Anode (red) and cathode (blue) layers.

  1. Step 1: Pick a Good Time.
  2. Step 2: Build Your LED Layers.
  3. Step 3: Test Each LED.
  4. Step 4: Soldering LED Layers.
  5. Step 5: Solder the Layers Together.
  6. Step 6: Building Your Cube’s Circuit.
  7. Step 7: Wiring the Board.
  8. Step 8: Code and Programming.

What is Arduino Nano?

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328P released in 2008. It offers the same connectivity and specs of the Arduino Uno board in a smaller form factor. In 2019, Arduino released the Arduino Nano Every, a pin-equivalent evolution of the Nano.

Can Arduino Nano output 5V?

The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.

Does Arduino Nano have 5V output?

The Nano has one 3.3V and two 5V power pins of which one is the VIN pin. With the VIN pin you can supply the Arduino Nano with a voltage between 7V-12V to run the microcontroller on battery for example. All three power pins provide a maximum currency of 50 mA. You can close the circuit with two ground pins.

How to make a 4x4x4 led cube with Arduino Uno?

Carve away the plastic ribs in the interior of the box near the hole with a knife, then hot glue the switch in place. Next, plug the pin headers and the 9v power supply into the Arduino Uno. Lastly, upload the code (sketch) to the Arduino then tighten the bottom lid on to project box. Now the 4x4x4 LED cube is finally finished!

How many LEDs are in a 4x4x4 led cube?

In this tutorial I’ll show you how to make a 4x4x4 LED cube for around $15.00. The cube has 64 green LEDs which make up it’s 4 layers (positives) and 16 columns (negatives). These are all wired to a Arduino Uno.

What is an led cube?

As we all know, an LED Cube is a bunch of LED that arranged in a cube shape that can perform some interesting lighting effects according to your program.

What is the Arduino Uno made out of?

The hardware consists of an open-source hardware board designed around an 8-bit Atmel AVR microcontroller, or a 32-bit Atmel ARM. I programed code (sketches) for the Arduino Uno to controll the individual LEDs to display patterns for this captivating desktop light show. If playback doesn’t begin shortly, try restarting your device.