How do I see the route table in Juniper?

How do I see the route table in Juniper?

show route table

  1. Syntax. content_copy zoom_out_map.
  2. Syntax (EX Series Switches, QFX Series Switches) content_copy zoom_out_map.
  3. Description. Display the route entries in a particular routing table.
  4. Options. brief | detail | extensive | terse.
  5. Required Privilege Level. view.

What does the output of the show route forwarding table?

Display the Routing Engine’s forwarding table, including the network-layer prefixes and their next hops. This command is used to help verify that the routing protocol process has relayed the correction information to the forwarding table. The Routing Engine constructs and maintains one or more routing tables.

How do I view routing table?

To display the kernel routing table, you can use any of the following methods:

  1. route. $ sudo route -n. Kernel IP routing table. Destination Gateway Genmask Flags Metric Ref Use Iface.
  2. netstat. $ netstat -rn. Kernel IP routing table.
  3. ip. $ ip route list. 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.103.

Which operational command displays the routing table?

Use the display ip routing-table verbose command to display detailed information about all routes in the routing table. This command displays detailed information about all active and inactive routes, including the statistics of the entire routing table and information for each route.

How do I check my route on Juniper?

show route-map

  1. Syntax. show route-map [ listName ] [ filter ]
  2. Release Information. Command introduced before JunosE Release 7.1.
  3. Description. Displays all the route maps or the route map you specify. The default is all route maps.
  4. Options.
  5. Mode. Privileged Exec.

How do I find my ip route in Juniper?

show ip route

  1. Syntax. show ip route [ vrf vrfName ] [ destination [ ipMask ] [ detail ] ] [ all ] [ protocol ] [ filter ] To display summary information:
  2. Release Information. Command introduced before JunosE Release 7.1.
  3. Description. Displays current state of the routing table.
  4. Options.
  5. Mode. Privileged Exec, User Exec.

What is the difference between routing table and forwarding table?

Routing tables contain network addresses and the associated interface or nexthop. This refers to ip route and ip rule (in a Linux context). Forwarding refers to packets which reach a system but are not destined for this system. “forwarding” is a common term in the context of packet filters.

What are two functions of the packet forwarding engine choose two?

The Packet Forwarding Engines provide the Layer 2 and Layer 3 packet switching, forwarding, and route lookup functions. In a maximum configuration with eight Type 3 FPCs installed, the Packet Forwarding Engines can forward up to 640 million packets per second (Mpps) for all packet sizes.

How do I find the default route and routing table?

Click Start, click Run, type cmd in the Open box, and then click OK. Type route print, and then press ENTER to view the routing table. Note the interface number of the network interface that you re-added. Type route print to verify that the new default route appears in the routing table.

What is Flag in routing table?

The U flag indicates that the route is up. The G flag indicates that the route is to a gateway. The H flag indicates that the destination is a fully qualified host address, rather than a network. The Refcnt column shows the number of active uses per route, and the Use column shows the number of packets sent per route.

How do I show VRF on Juniper?

show ip vrf

  1. Syntax. show ip vrf [ [ detail ] [ vrfName ] | interfaces [ detail ] ] [ filter ]
  2. Release Information. Command introduced before JunosE Release 7.1.
  3. Description.
  4. Options.
  5. Mode.

How do I check the VRF route in Juniper?

What does the optional option do in a route table?

(Optional) Perform this operation on all logical systems or on a particular logical system. This option is only supported on Junos OS. Display route entries for all routing tables whose names begin with this string (for example, inet.0 and inet6.0 are both displayed when you run the show route table inet command).

How does Junos announce a BGP route?

The number of BGP peers or protocols to which Junos OS has announced this route, followed by the list of the recipients of the announcement. Junos OS can also announce the route to the kernel routing table (KRT) for installing the route into the Packet Forwarding Engine, to a resolve tree, a Layer 2 VC, or even a VPN.

How can junjunos OS announce the route to the KRT?

Junos OS can also announce the route to the KRT for installing the route into the Packet Forwarding Engine, to a resolve tree, a L2 VC, or even a VPN. For example]

What is the difference between preference2 and localpref in Junos?

In order to use common comparison routines, Junos OS stores the 1’s complement of the LocalPref value in the Preference2 field. For example, if the LocalPref value for Route 1 is 100, the Preference2 value is -101. If the LocalPref value for Route 2 is 155, the Preference2 value is -156.